Updated Dec-2023 Test Engine to Practice NACE-CIP2-001 Test Questions
NACE-CIP2-001 Real Exam Questions Test Engine Dumps Training With 100 Questions
NEW QUESTION # 46
Inspection and Test Plans are provided to:
- A. To supersede the requirements of the product data sheets
- B. So the Inspector doesn't have to read the entire specification
- C. Outline the inspection steps, sequencing and pass/fail criteria
- D. So the contractor has a single document to reference
Answer: C
NEW QUESTION # 47
The Inspectors' goal at the Pre-Job Conference is to:
- A. Obtain a clear understanding of the Specification
- B. Take accurate meeting minutes for distribution
- C. Manage the meeting so it doesn't go off topic
- D. Discuss contractual requirements
Answer: A
NEW QUESTION # 48
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. True
- B. False
Answer: B
NEW QUESTION # 49
Individuals conducting Coating Surveys should:
- A. Always be trained and experienced Coating Industry
- B. Always be experienced Specification Writers
- C. Always be NACE Level 3 Certified Inspectors
- D. Always be NACE or SSPC Protective coating Specialists
Answer: A
NEW QUESTION # 50
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Use a generally accepted industry standard and to take readings
- B. Refuse to take readings until an is in place
- C. Develop your own methodology and proceed take the readings
- D. Call your supervisor
Answer: A
NEW QUESTION # 51
NACE International Standards are developed by:
- A. International mandates
- B. Standard committees
- C. Government mandates
- D. Regional mandates
Answer: B
NEW QUESTION # 52
Dehumidification is defined as the removal of moisture vapor from the air to
- A. raise its relative humidity.
- B. lower its temperature
- C. provide worker comfort.
- D. lower its dew point,
Answer: D
NEW QUESTION # 53
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. True
- B. False
Answer: A
NEW QUESTION # 54
An Inspection and Test Plan is required when:
- A. When the Inspector requests one
- B. When the Owner specifies one
- C. It is always required
- D. When the Coating Applicator requests one
Answer: C
NEW QUESTION # 55
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. Coal Tar Enamel
- B. 2-Layet Polyethylene (PE)
- C. 3-Layet Polyethylene (PE)
- D. Concrete
Answer: D
NEW QUESTION # 56
When performing an adhesion test in accordance with ASTM D 3359 where the Dry Film Thickness is approximately 10 mils, the Inspector should use:
- A. Method B - X cut
- B. Method A - Cross Hatch
- C. Method A - X Cut
- D. Method B - Cross Hatch
Answer: C
NEW QUESTION # 57
Examples of non-ferrous metals include
Select All that Apply:
- A. copper
- B. iron
- C. mild steel.
- D. aluminum
Answer: A,D
NEW QUESTION # 58
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Glue failure
- B. Cohesion failure
- C. Adhesion failure
- D. Cold flow or creep
Answer: D
NEW QUESTION # 59
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. Another NACE Level 2 Inspector
- B. A NACE Level 3 Inspector
- C. A NACE Level 1 Inspector
- D. A NACE Protective Coating Specialist
Answer: B
NEW QUESTION # 60
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. Sacking
- B. High-pressure water washing
- C. Acid etching
- D. Stoning
Answer: A
NEW QUESTION # 61
From a corrosion perspective, the main difference between Ferrous and Non-Ferrous Metals is:
- A. Cost
- B. Safety
- C. Appearance
- D. Iron content
Answer: D
NEW QUESTION # 62
Thermal Spray coatings provide:
- A. Inhibitive protection
- B. Thermal protection
- C. Barrier protection
- D. Sacrificial protection
Answer: D
NEW QUESTION # 63
Ideally, documentation requirements should be defined:
- A. By the inspector
- B. At the pre-job conference
- C. In the specification
- D. By the contractor
Answer: C
NEW QUESTION # 64
When environmental enclosures are being used an inspector needs to be concerned about:
- A. Structural integrity
- B. Air changes
- C. a), b), and c)
- D. Lighting
Answer: C
NEW QUESTION # 65
You are working as an inspector in a galvanizing plant for the first time.
What are some of the hazards you need to be aware of:
- A. Risk of skin
- B. Risk of chemical exposure
- C. a), b), and c)
- D. Risk of acid or caustic splashes
Answer: C
NEW QUESTION # 66
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
Answer: B
NEW QUESTION # 67
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Ignore the additional requirement
- B. Enforce the additional requirement
- C. Call your supervisor
- D. Request clarification from the specifier
Answer: B
NEW QUESTION # 68
External coatings applied to buried pipelines are generally tested for:
- A. Cathodic disbondment
- B. Solvent resistance
- C. Chalking resistance
- D. Gloss level
Answer: A
NEW QUESTION # 69
When performing inspection in accordance with ASTM D 4138 the Inspector will use:
- A. A set of 14 pencils of varying hardness
- B. A destructive paint inspection Tooke gauge
- C. A mechanical adhesion tester
- D. A hardness tester
Answer: B
NEW QUESTION # 70
......
NACE-CIP2-001 Actual Questions Answers PDF 100% Cover Real Exam Questions: https://passleader.realexamfree.com/NACE-CIP2-001-real-exam-dumps.html
