CQE Certification Exam Dumps Questions in here [Mar-2024]
Updated CQE Exam Practice Test Questions
NEW QUESTION # 25
The use of 100% inspection normally means
- A. That the final customers will not experience defective product.
- B. That the lowest over-all quality costs have been considered.
- C. That there will be an opportunity to rework any product deemed to be outside of specifications.
- D. That selected characteristics have been evaluated against specified standards.
Answer: D
NEW QUESTION # 26
When used together for variables data, which of the following pair is the MOST useful in preparing control charts?
- A. X-bar and R
- B. p, n
- C. R, sigma
- D. AQL, p-bar
Answer: A
NEW QUESTION # 27
A two-way analysis of variance has r levels for one variable and c levels for the second variable with 2 observations per cell. The degree of freedom for interaction is
- A. 2(r)(c)
- B. (r-1)(c-1)
- C. 2(r-1)(c-1)
- D. rc-1
Answer: B
NEW QUESTION # 28
Which of the following quantitative methods does NOT apply to the assessment of actual system/component reliability?
- A. Statistical allocation of reliability goals.
- B. Statistical analysis of field test and failure data.
- C. Evaluation of laboratory test data.
- D. Analysis of results of reliability demonstration tests.
Answer: A
NEW QUESTION # 29
The AQL for a given sampling plan is 1% this means that
- A. All accepted lots are 1% defective or better.
- B. The producer takes a small risk of rejecting product which is 1% defective or better.
- C. All lots are 1% defective or better.
- D. The average quality level of the plan is 1%.
Answer: B
NEW QUESTION # 30
The existence of a quality control manual at your key supplier means
- A. That the firm is quality conscious.
- B. That the firm is a certified supplier.
- C. That a quality system has been developed.
- D. That a quality system has been implemented.
Answer: C
NEW QUESTION # 31
An X-bar and R chart with n=5 has been plotted for some time and has demonstrated random variation.
Upon review of the last 30 plot points, the expected number of runs around the centerline on the X-bar chart is expected to be approximately which of the following?
- A. 0
- B. 1
- C. 2
- D. 3
Answer: A
NEW QUESTION # 32
An electronics firm was experiencing high rejections in their multiple connector manufacturing departments. "p" charts were introduced as part of a program to reduce defectives. Control limits were based on prior history, using the formula:
P' is the historical value of percent defective and n is the number of pieces inspected each week. After six weeks, the following record was accumulated
1,000 pieces were inspected each week in each department. Which department(s) exhibited a point or points out of control during this period (round off calculations to nearest tenth of a percentage point)?
- A. Department 106.
- B. Department 104.
- C. All of the department.
- D. Department 105.
Answer: C
NEW QUESTION # 33
During the building phase of improvement team development, which of the following properly describes team activities?
. The team leader is usually directive.
. The team leader often delegates tasks.
. Team members prioritize and perform duties.
. Team members are uncertain of their duties.
- A. IIandIIIonly
- B. II,IIIandIV only
- C. IandIV only
- D. I,IIandIIIonly
Answer: C
NEW QUESTION # 34
The first and most important step, in establishing a good corporate quality plan is
- A. Determining manufacturing process capabilities.
- B. Ensuring quality participation in design review.
- C. Evaluation vendor quality systems.
- D. Determining customer requirements.
Answer: D
NEW QUESTION # 35
Which of the following statements is CORRECT?
- A. Regression estimates are better made with positive correlation than with negative correlation.
- B. The higher the correlation, the better the regression estimate.
- C. The better the regression estimate, the greater the likelihood that homoscedasticity exists with therespect to the predicted variable.
- D. The lower the correlation, the greater the likelihood that homoscedasticity exists with respect to thepredicted variable.
Answer: B
NEW QUESTION # 36
What percentage of the area under the standard normal curve is included within (+/-) 1.5 standard deviations from 0?
- A. 0.6680
- B. 0.7500
- C. 0.9332
- D. 0.8664
Answer: D
NEW QUESTION # 37
Which of the following is the BEST method to developing materials for a training program on the gaps in performance?
- A. Review a record of activities.
- B. Set up a one shot case study.
- C. Secure a workshop trainer.
- D. Allocate employees for training.
Answer: A
NEW QUESTION # 38
A purchase order for subassemblies classified as critical must include a review by
I. Quality engineering.
II. The procurement department.
III. Design engineering.
- A. III only
- B. II and III only
- C. I, II and III
- D. I and III only
Answer: C
NEW QUESTION # 39
Applications for surface plate includes which of the following?
I. Referencing plane for length measurements.
II. Referencing plane for parallelism measurements.
III. Establishing a datum plane for dimensional layout.
IV. Waiting place for delicate parts.
V. Keeping extra gages when not in use.
- A. I and IV only
- B. I and II only
- C. I, II and III only
- D. III and V only
Answer: C
NEW QUESTION # 40
......
Pass ASQ Certification CQE Exam With 162 Questions: https://passleader.realexamfree.com/CQE-real-exam-dumps.html
